2/28/12 PN 96508 v.7.0 Banks Six-Gun®Diesel TunerCompatible with Optional Banks PowerPDA®For use with Palm® Tungsten™ E2 only2007- 2010 Chevy/GMC 6.
10 96508 v.7.010. Position the Tuner on the fuse box cover for an idea of where to clean. The Tuner must be mounted as close to the inside (engine s
96508 v.7.0 11If not installing the optional Banks PowerPDA, skip to Section 3.1. Locate the universal mount and docking station in your kit. Interl
12 96508 v.7.07. For the cleanest PowerPDA installation (Figure 7), remove the fuse access panel by pulling it out from the side of the dash. Route
96508 v.7.0 13is fuse protected, the user is expected to take appropriate measures to prevent small children and/or pets from contact with any part
14 96508 v.7.0Not needed if the optional Banks PowerPDA is installed.CAUTION: Do not use force when working on plastic parts. Permanent damage to th
96508 v.7.0 15Figure 12Figure 13Figure 14
16 96508 v.7.0bolster panel by removing the 2 Phillips screws on the lower edge of the panel. Using a 10mm socket and ratchet, unbolt the brake rele
96508 v.7.0 17Figure 16- Rear template usedFigure 17
18 96508 v.7.010. After confirming the locating washer is in the #6 location, install the Switch through the 3⁄8” hole. The alignment pin should res
96508 v.7.0 191. The thermocouple monitors the temperature of the exhaust gases entering the turbocharger at the turbine housing. Installation requi
2 96508 v.7.0 THIS IS A HIGH PERFORMANCE PRODUCT. USE AT YOUR OWN RISK.Do not use this product until you have carefully read the following agreement
20 96508 v.7.0NOTE: Please refer to the Banks PowerPDA Software & Installation Kit Owner’s Manual for software installation and operation instru
96508 v.7.0 21The Six-Gun Diesel Tuner requires the engine coolant temperature (ECT) to be above 110º before it will add fuel. If the optional Banks
22 96508 v.7.0Six-Gun troubleshooting using the Banks PowerPDA.Check the Banks PowerPDA’s Status Indicator for the “OK” icon. Any Six-Gun Tuner faul
96508 v.7.0 23Six-Gun Troubleshooting using the Tuner’s LEDs.(With or without a Banks PowerPDA Installed)If you feel that your Six-Gun Diesel Tuner
24 96508 v.7.0Code PDA Error Message Corrective Action1,1Fuel Rail Pressure (FRP) Input Voltage Out of Range.Turn ignition OFF for 60 seconds and ch
96508 v.7.0 25If the Six-Gun Diesel Tuner has been moved to a different vehicle, or you are instructed to do so by Banks Technical Staff, it is poss
26 96508 v.7.0Section 10PLACEMENT OF THE BANKS POWER DECALSTYPICAL LEFT FENDER PLACEMENTTYPICAL RIGHT FENDER PLACEMENTFigure 25
96508 v.7.0 27Figure 23- Use only when drilling from the frontFigure 24- Use only when drilling from the rear
Gale Banks Engineering 546 Duggan Avenue • Azusa, CA 91702 (626) 969-9600 • Fax (626) 334-1743Product Information & Sales: (888) 635-4565bankspowe
96508 v.7.0 3limited to a period of 90 days from purchase. All products that are in question of warranty must be returned shipping prepaid to the SE
4 96508 v.7.0 Dear Customer,If you have any questions concerning the installation of your Banks Six-Gun Diesel Tuner, please call our Technical Serv
96508 v.7.0 5TOOLS REQUIRED:• Inch and metric sockets• Inch and metric combination andopen-end wrenches• Pliers• Wire cutters or scissors• Center pu
6 96508 v.7.0Description Part Number Kit63892 63887Module, Six-Gun Diesel Tuner 63886 1 1Switch Kit 62139 1Cable Ties, 7” 62010 15 20PowerPDA Dockin
96508 v.7.0 71. Disconnect the battery ground cables from each of the batteries. Secure the cables so that they do not come in contact with the batt
8 96508 v.7.0NOTES: A small screwdriver may help in lifting the blue connector locks. Take care not to break the plastic on the connectors. It may b
96508 v.7.0 9spot that was cut from the outside. Now, feed the In-Cab cable through the incision made in the firewall grommet and into the cab (Figu
Kommentare zu diesen Handbüchern